JavaScript is disabled. For a better endure, please enable JavaScript in your web browser before proceeding.

You are watching: Why is oil coming out of my dipstick


bought a automobile through this motor in it it has 40 lbs oil pressure all times however as soon as idled up oil comes out the tube and everywhere the headers and driver side engine compartment.the engine has been modified yet the male i acquired it from knew very little around it.it has actually high increase intake angle port heads demon carb etc... please help me number this thing out prior to i pull my hair out.................. lol
oil coming out of dipstick tube 350 2 bolt mainwhat will cause oil to come out the dipstick tube? i just bought the car and dont know alot about it any kind of help is apreciated
Re: oil coming out of dipstick tube 350 2 bolt main
overflow of oil, did you put more than u were mean to
Re: oil coming out of dipstick tube 350
Have ya obtained a P.C.V system from ya filler caps on both valve covers???If not try taking the filler caps off/out and also idle the automobile to watch if theoil difficulty is still there,If so then a compression leak dvery own test to check out if theres excess compression leaking into the sump and pressurizing it,If its a "stroker" motor you deserve to getalot more disturbance stirred up by the rotating crank shaft,But if its badat idle it have to be alot worse at complete rev"sIts a begin..Gav
Re: oil coming out of dipstick tube 350
no pvc system but did take the caps off both valve covers and oil still came out of the dipstick tube when reved up yet once it idles it doesnt come out of the oil tube.
Re: oil coming out of dipstick tube 350 2 bolt main
the oil level is on the mark on the dipstick, it just comes out as soon as we idle the motor up. at a idle it does not come up the tube .
Re: oil coming out of dipstick tube 350 2 bolt main
Overfull or a significant blow-by issue deserve to cause it. The height of the dipstick need to have a rubber seal in it. Is the seal damaged?
Dave========================68 Coupe, 350 w/ Edelbrock Performer RPM heads, cam, intake, 700R4, Dave"s small body HEI
Re: oil coming out of dipstick tube 350 2 bolt main
Is the PVC valve functioning properly? Also attempt an oil Breather/Filler Cap, like the one bellow. if this does not help, then you might have actually a blow-by case.
*

Re: oil coming out of dipstick tube 350 2 bolt main
Sounds like the pcv system is not functioning..make sure your pcv is brand-new or cleaned out or unclogged and the same with the breather filter on the various other valve cover too..make certain the pcv hose is pulling vac as soon as the automobile is running!..ALSO CHECK THE VC"S, IF THEY ARE AFTERMARKET SOMEBODY MIGHT HAVE THE BAFFLE CLOSED OFF ON THE UNDERSIDE OF THE VC(ANOTHER WORDS THE VENT IS NOT OPEN OR ABLE TO PULL)
BILL D.JOHN 3:16 SEMPER FIif you have actually a bbc in your first gen 67-69 camaro click the link below and reap the veiw and post yours up!!:yes:http://www.jiyuushikan.org/forums/showthread.php?t=169199if you have actually an all original 1st gen camaro 67-69 click on the link listed below and also reap the veiw and also post your up!!:yes:http://www.jiyuushikan.org/forums/showthcheck out.php?t=179697
Re: oil coming out of dipstick tube 350
a.oil level correct?b. dipstick might be wrong. I would certainly drain the pan and put 5 quarts ago in, examine versus mark on stick.
Re: oil coming out of dipstick tube 350 2 bolt main
Your engine must not be blowing oil out of the dipstick tube. That is evidence of also a lot crankinstance press. Generally, this is resulted in by a negative head gasket (cylinder head press leaking right into the crankcase). Rule out the basic stuff first. Rerelocate the PCV and shake it. Can you hear the sphere bearing inside? If yes, put it ago in, its most likely fine. Do you have a breather? If yes and also it does not look all crungy, its additionally probably fine. Then, execute a compression test. A compression gauge is cheap and this is somepoint you deserve to do in the drivemethod through a helper to rotate the crucial. Look for one cylinder a lot lower than the rest. If so, rearea both head gaskets.

See more: Does Ralph Understand Why He Must Be Killed ? Lord Of The Flies Flashcards


Re: oil coming out of dipstick tube 350
oil level dead on mark however it does have actually a aftermarket stick i will certainly attempt altering the oil and also see
Re: oil coming out of dipstick tube 350 2 bolt main
many thanks men i will certainly try the suggestions tomorrow and will upday then
Re: oil coming out of dipstick tube 350 2 bolt main
I know this is an old thcheck out, but did you ever number out the trouble, bereason my chevy 350 is doing the very same thing?
*

When was the last filter and oil change?Easy to drainpipe, and make sure its not over filled.If it is not that try these widespread factors for oil blow outPVC is functioning? - Many prevalent problem breather is clogged or valve is malfunctioning Compression ok on all 8? Rings are okay?Guides okay?These 3 seem to take a trip together....Run each as much as TDC and usage 100 psi in the spark plug hole and listen for death rattle in heads or carb or exhaust.
:waving:1969 Z11 Pace Car - L48 350cid/300hp - 4 Speed Muncie 12 bolt rear. Super Moderator
Team Camaro Click here to send me a personal message
Re: oil coming out of dipstick tube 350 2 bolt main
I understand this is an old thread, yet did you ever figure out the trouble, bereason my chevy 350 is doing the very same thing?
*
Continue with Google
A forum neighborhood dedicated to 1st generation Chevy jiyuushikan.org owners and also enthusiasts. Come sign up with the discussion about performance, builds, restoration, modifications, classifieds, troubleshooting, reviews, and more!