From year to year, Cisco has updated many kind of versions through distinction concerns. The latest variation is variation 6.0 in 2018. What is your version? It counts on your instructor developing your class. We recommfinish you to go thought all version if you are not clear. While you take virtual test with netacad.com, You may gain random inquiries from all version. Each version have 1 to 10 different concerns or more. After you testimonial all inquiries, You have to exercise via our digital test system by go to "Online Test" link below.

You are watching: Why do ospf serial interfaces usually require manual bandwidth configuration

Version 5.02Version 5.03Version 6.0Online Assessment
Chapter 6 ExamChapter 6 ExamChapter 6 ExamOnline Test
Next off Chapter
Chapter 7 ExamChapter 7 ExamChapter 7 ExamOnline Test
Lab Activities
 6.2.2.4 Packet Tracer – Configuring Basic EIGRP through IPv4
 6.3.4.4 Packet Tracer – Investigating DUAL FSM
 6.4.3.4 Packet Tracer – Configuring Basic EIGRP via IPv6 Routing

Why carry out OSPF serial interencounters typically need hands-on bandwidth configuration?

OSPF provides the bandwidth value to compute courses for its routing table.Each side of an OSPF serial connect have to be configured with a distinctive worth.All serial interdeals with default to a value of 1.544 Mb/s.Bandwidth value affects the actual rate of the link.

Which statement describes a multiarea OSPF network?

It is composed of multiple network areas that are daisy-chained together.It calls for a three-layer ordered network architecture approach.It has a core backbone area via other locations associated to the backbone location.It has multiple routers that run multiple routing protocols concurrently, and also each protocol consists of a room.

What is one benefit of making use of multilocation OSPF?

It permits OSPFv2 and OSPFv3 to be running together.It permits multiple routing protocols to be running in a large netoccupational.It increases the routing performance by splitting the neighbor table into sepaprice smaller sized ones.It boosts the routing effectiveness by reducing the routing table and link-state update overhead.

Which characteristic describes both ABRs and ASBRs that are imposed in a multiarea OSPF network?

They commonly have actually many type of neighborhood networks attached.They both run multiple routing protocols simultaneously.They are compelled to perform any kind of summarization or recirculation work.They are compelled to repack typically and conveniently in order to upday the LSDB.

What is used to facilitate hierarchical routing in OSPF?

autosummarizationthe usage of multiple areasregular SPF calculationsthe election of designated routers

Which two statements effectively define OSPF form 3 LSAs? (Choose two.)

Type 3 LSAs are known as autonomous system outside LSA entries.Type 3 LSAs are produced without requiring a full SPF calculation.Type 3 LSAs are supplied for courses to networks exterior the OSPF autonomous mechanism.Type 3 LSAs are recognized as router connect entries.Type 3 LSAs are offered to upday routes between OSPF areas.

What OSPF LSA form is used to inform routers of the router ID of the DR in each multiaccess netjob-related in an OSPF area?

type 1type 2form 3kind 4

What form of OSPF LSA is originated by ASBR routers to advertise exterior routes?

form 1type 2type 3form 5

Refer to the exhilittle bit. What deserve to be concluded around network-related 192.168.4.0 in the R2 routing table?

*
*
*
CCNA3 Chapter 6 v5.03 004The enattempt for 172.16.200.1 represents a loopago interconfront.The routing table consists of routes from multiple locations.To reach netjob-related 172.16.2.0, web traffic will travel via the GigabitEthernet0/0 interface.The routing table has two intra-location paths.To reach netoccupational 192.168.1.0, website traffic will departure by means of the Serial0/0/0 interconfront. 

Which command can be provided to verify the contents of the LSDB in an OSPF area?

present ip ospf databasedisplay ip ospf interfacepresent ip ospf neighborshow ip route ospf

Match each form of OSPF router to its description. (Not all choices are used.)

Open the PT Activity. Perdevelop the jobs in the task instructions and then answer the question.

What is avoiding individuals that are linked to rexternal R2 from accessing sources located either within the network-related 192.168.1.0 or the internet?

The default course is not redispersed appropriately from rexternal R1 by OSPF.The interconfront that is linked to the ISP is dvery own.The router R2 is not receiving any type of updates from either router R1 or R3.The OSPF network statements are misconfigured on among the routers.The OSPF timers that are configured on routers R1, R2, and R3 are not compatible.

Open the PT Activity. Perform the tasks in the task instructions and also then answer the question.

See more: In The Term Osteomyelitis, What Does The Root Myel Refer To?

Fill in the blank. Do not usage abbreviations.

What is the missing command on router R2 to create an adjacency in between routers R1 and R3?

netjob-related 172.16.10.0 0.0.0.255 area 0